Meyer Sound CueMixer Matrix3 Guia do Utilizador

USER GUIDE LCS SERIESCueMixerMatrix3 Audio Show Control SystemEdition: 2007-09-19 for CueStation 4.6.0

10

CueMixer ControlsModes 12Page Select 12Transport Buttons 13EQ 14Isolate 14Mute 14User Buttons 14Controls on the CueMixer are organized into sections w

ModesNext to each button is an LED. On the top two rows of buttons, these LEDs are used to display the current modeand page selection.There are four m

For example, to select faders 33 to 40, you need “page 5”. Press then release the Shift key (LED lights) then pressthe Isolate button for fader number

that will allow automated levels to be offset. For example if you have a substitute musician and you need to adjustthe overall level without changing

Programming CueMixer FunctionsCueMixer Setup 15User A Mode 19CueMixer SetupBy default the LX-300 connection to CueMixer is not enabled. An External Su

Enable Console ModesEnables these controls on the CueMixer. By default these are all of enabled until you use this command and select"Disable&quo

Enable Misc Console ModesEnables these controls on the CueMixer. By default these are all of enabled until you use this command and select"Disabl

NoteDo not confuse User A button with User A mode. User A button fires a single cue when pressed. When you enterUser A mode (LED next to user A button

Set Port on LX-300Port B on the LX-COS module is the default port for connecting a CueMixer, but you can change the connection toPort A. Please note t

Meyer Sound Laboratories Inc2832 San Pablo AvenueBerkeley, CA 94702www.meyersound.comT: +1 510 486.1166F: +1 510 486.8356© 2007Meyer Sound Laboratorie

20

Using the CueMixerMixing with Virtual Groups 21Executing Cues with User A Buttons 21Connect the CueMixer to a Matrix3 LX-COS module (Port B is the def

22

CueMixer DetailsBasic Operation 23Reference 24Basic OperationWhen the CueMixer is first powered up it starts with System Master as the current mode. T

ReferenceThe following section provides details for each, LED, button and feature found on the CueMixer.First Row of LEDsThe mode LEDs are used to ind

ShowThis causes the Status display on the front of the LX-300 to show the next cue in the active Cue List. The statusdisplay is in the form “Nxxx” Whe

(Shifted) [c.NEW]: Cue Lists window- Makes a new cue entry with the default name, captures all, and then putsit in a cue list. A Cue List must be sele

Third Row of LEDsThe third row of LEDs and the third row of buttons are used to show a channel has been Isolated from automation.When EQ is active, th

28

Service and TroubleshootingService 29Calibration 29When power is first applied to the CueMixer, it runs through a self-test. The LEDs turn on one row

© 2007 Meyer Sound. All rights reserved.CueMixer User GuideThe contents of this manual are furnished for informational purposes only, are subject to c

There are four circuit boards in the unit. There is a board that has all of the push-button switches and LEDs mountedon it. Mounted above this is a ci

Trim Adjustment LocationsCPUBoardDB-9FaderBoardFaderBoardT1T1 T1Resetting Trim AdjustmentsIf minor adjustments do not align the faders, or if the trim

32

Table of ContentsCueMixer™ Setup 7Connecting the CueMixerCueMixer Controls 11ModesPage SelectTransport ButtonsEQIsolateMuteUser ButtonsProgramming Cue

6

CueMixer SetupConnecting the CueMixer 7The CueMixer™ is a physical control surface for the Matrix3™ audio show control system. The faders and buttonsp

RS-422CueMixer LX-COS modulePort BRS-422 Serial CableOn the Matrix3 LX-COS module, Port A and Port B use the same connector pin-outs as the CueMixer,

Table 1. CueMixer RS-422 ConnectionPurposePinShield1TxD+4TxD-5RxD+8RxD-9DIP Switch SettingsThe dip-switches on the rear panel of the CueMixer are not